Featuring Fail Safe, USB & Quick Boot Modes
SVGA			Audio COM 1 & 3 multiPort: Parallel Floppy(*) aDIO™ Utility: Keyboard Mouse Speaker Battery Reset
LVDS   COM 2 & 4     2 USB 2.0   Ethernet   100Base-Tx   10Base-T
	Power	EIDE
	CMX158886PX1400HR-BRG-512 Dual Board cpuModule with PCI to ISA Bridge Module and Mini Fan Heatsink installed
CMX158886PX Bridge Module PCI Slot 0  ISA        (PC/104)			PCI  (PCI-104)
	Rugged Fanless IDAN & HiDAN Configuration -40°C to +85°C
	(*)  Interfaces only with RTD modified floppy drive Solder-tail expansion bus, right-angle I/O & feed-thru I/O connectors available on request

Features:

• 1.4 GHz  Intel Pentium M with thermal throttling
• Complete PC-compatible Single Board Computer
• Nonvolatile storage of CMOS settings without battery
• Stackable 104-pin PC/104 AT bus
• Stackable 120-pin PCI bus
  • 4 Bus master add-on cards capable
• 512 Mbytes & 1GB BGA DDR SDRAM
  • Up to 333 MHz Data Rate
  • ECC (Error-Correction Codes) corrects single-bit memory
    errors and detects 2-bit errors (available on 512MB model)
• 32 pin SSD socket supports:
  • Miniature 4GB ATA/IDE Flash Disk installed unless otherwise specified
  • Natively supported by all major operating systems
• BIOS Selectable multiPort with Parallel, Floppy Drive Interface and 18-bit Digital I/O with Advanced Digital Interrupt Modes
• Additional 18-bit BIOS Selectable Digital I/O
• 10/100 Ethernet with PXE Network Boot
• Four RS-232/422/485 Ports
• Two USB 2.0 (Universal Serial Bus) Ports
• EIDE Controller with UltraDMA 100
• 855GME SVGA controller Onboard with 3D Acceleration
• DirectX & OpenGL 3D Accelerator
• AC97 Audio Support
• Advanced power management features including
  Enhanced Intel SpeedStep Technology
• Advanced Thermal Management
  • Thermal Throttling reduces clock speed to
    prevent thermal runaway
  • Auto Fan Control only runs fan when needed
  • SMBus Temperature Monitor for CPU and board temperature
  • Mini Fan Heatsink with Auto Fan control
  • Passive Structural Heatsink & Heatpipes in IDAN and HiDAN System Configurations
• Advanced Programmable Interrupt Controller (APIC)
• 24 interrupt channels with APIC enabled (15 in legacy PIC mode)
• 3 timer/counter channels
• High resolution 100 MHz APIC timer
• RTD Enhanced AMI BIOS with ACPI, USB Boot and Quick Boot modes
• Advanced Configuration and Power Interface (ACPI)
  • ACPI 1.0 Compliant
  • Supported power down modes: S1 (Power On Suspend), S3 (Suspend to RAM), S4 (Hibernate), and S5 (Soft-Off)
  • CPU Clock Throttling and Clock Stop for C0 to C3 Support
  • Also supports APM 1.2 for legacy power management
• 3.3V or 5V PCI bus signaling
• 400 MHz, source-Synchronous Front Side Bus
• Supports MMX and SSE2 instructions
• Math coprocessor
• Internal Cache
  • L1 - 32KB of instruction and 32KB data; L2 - 2MB
• Y2K compliant real time clock (external battery required)
• Watchdog timer
• PS/2 Mouse Port
• Keyboard Port
• Speaker Port

I/O:

• AC97 Audio Support
  • Selectable Headphone or Line level output
  • Line level input
  • Microphone input
• Fast Ethernet
• Ethernet Controller
  • Intel 82562 Fast Ethernet PCI Controller
  • Integrated 3KByte Transmit and 3Kbyte Receive FIFOs
• Physical Layer
  • 100Base-Tx and 10Base-T
  • Full Duplex support
• Easy to Use
  • Low Power Features
  • LED Status
  • Software configuration
• 855GME SVGA controller for CRT and LVDS Flat Panel
  • Analog SVGA Output
  • LVDS Flat Panel output
  • Resolution up to 2048 x 1536 pixels with 32K colors
  • VGA, SVGA, XGA, SXGA, UXGA
  • Up to 16 million colors
  • 64-bit AGP Hardware graphics-accelerator
    • 2MB to 64MB of shared SDRAM high-performance memory
• Four BIOS configurable RS-232/422/485 serial ports on two connectors, each connect configurable as:
  • One full RS-232 port with TxD, RxD, CTS, RTS, DSR, DTR, RI, and CD
  • One RS-422/485 port with TxD+, TxD-, RxD+, RxD-, with 120 ohm termination jumper
  • Two RS-232 ports:
    • One with TxD, RxD, CTS, and RTS
    • One with TxD and RxD
  • One RS-232 port with TxD and RxD, and one RS-422/485 port with TxD+, TxD-, RxD+, RxD-, with 120 ohm termination jumper
  • Jumper enabled two RS-422/485 ports each with TxD+, TxD-, RxD+, RxD-, with 120 ohm termination jumper
  • 16550 compatible UARTs for high-speed
• multiPort function connector
  • Parallel port
    • SPP, PS/2 bi-directional, EPP & ECP
  • 36 Advanced Digital I/O (aDIO)
    • Two 8-bit port programmable as input or output
    • Sixteen bit-programmable I/O with Advanced Digital Interrupt Modes
      • Event Mode Interrupt generates an interrupt when any input bit changes
      • Match Mode Interrupt generates an interrupt when input bits match a preset value
      • External Strobe Mode latches 8 data inputs and generates and interrupt
    • Four Strobes can be configured as readable inputs.
  • Floppy controller interface - Interfaces only with RTD's XK-CM49 multiPort Floppy Drive and Cable Kit
• Two USB 2.0 (Universal Serial Bus) Ports
  • Supports 480 Mb/s (high-speed), 12Mb/s (full-speed), and 1.5Mbs (low speed) peripherals
  • 500 mA @ 5 Vdc provided per port
  • USB Boot capability
• UltraDMA-100 / 66 / 33 Master Mode PCI EIDE Controller
  • Transfer rate up to 100MB/sec using UltraDMA
  • Increased reliability using UltraDMA-33 transfer protocols
  • Support ATAPI compliant devices including DVD drives
  • 48-bit LBA support for hard drives larger than 137GB
• Utility port
  • XK-CM77 Cable Kit Included
  • PC-AT compatible keyboard port
  • PS/2 Mouse Port
  • Speaker (0.1W output) port
  • Hardware Reset input
  • Battery input for Real Time Clock
• Power I/O
  • Access to PCI-104 Bus pins
    • Gnd, ±12, 5 & 3.3 VDC
• ISA Expansion Bus
  • Full ISA bus operation.
  • Supports 8-bit (XT) and 16-bit (AT) peripherals.
  • All ISA IRQ lines and DMA channels supported.
  • Supports both I/O-mapped and Memory-mapped expansion cards.
  • Subtractive Decode of PCI cycles
    • Existing software can be used without modification.
    • No special setup required.
• Mating Connectors
  • Standard 12-pin 0.1" DIL header (Power)
  • Standard 10-pin 0.1" DIL header (Utility, COM1, COM2, USB, Ethernet)
  • Standard 10-pin 2mm DIL header (Audio & SVGA)
  • Standard 20-pin 2mm DIL header (Panel)
  • Standard 26-pin 0.1" DIL header (multiPort)
  • Standard 44-pin 2mm DIL header (EIDE)

Software:

• RTD Enhanced AMI BIOS with built-in SETUP, USB Boot and Quick Boot Mode Installed
  • Supports onboard video and PCI expansion bus video.
  • Hard drives supported by onboard IDE controller.
  • Floppy drives supported via USB Port and multiPort.
• Includes ROM-DOS , utilities and example programs.
• Compatible with all x86 operating systems:
  • MS-DOS, ROM-DOS, PC-DOS
  • Windows (98, NT 4.0, 2000, XP, and XP Embedded)
  • Linux (desktop and real-time versions)
  • RTOSes such as QNX, VxWorks, and Windows CE

Physical Attributes:

• Dimensions
  • Board Size: 90.17 mm L x 95.89 mm W (3.550 in L x 3.775 in W)
  • I/O Ext: 12.70 mm E_L x 79.38 mm E_W (0.500 in E_L x 3.125 in E_W)
• Weight: Approximately 0.28 Kg (0.62 lbs.)
• Standard Operating Temperature: -40° to +85°C: 90% humidity non-condensing
• Storage Temperature: -40° to +85°C
• MTBF: 110,000 hours typical
• Power requirements  1400 MHz:  13.7 W @ 5 VDC Typical

Recommended Accessories:

• Cable Kit XK-CM65

Documentation and Software Downloads:

• Hardware Manual
• BRG17088 Hardware Manual
• Drivers and Example Programs
• Software Manual(s)
• Application Notes

Ordering Information

* 4GB ATA/IDE Flash Disk installed unless otherwise specified.

Third Party Information     IDAN® Systems

CPU Guide     PC104 Menu     Accessories     Development Kits     Home

Copyright © 1998-2006 RTD Embedded Technologies, Inc.  All rights reserved.