SPM186420ER1000 Accelerator 
PCI-104 dspModule™
TMS320C6416 based Industrial DSP Module
Bus master or target only PCI Interface

	PCI Expansion Bus
Texas Instruments 500MHz TMS320C6416 Power			SyncBus
			McBSP
			McBSP
JTAG			McBSP
	PCI        rotary switch	DSP PlatformBus
	SPM186420ER1000-256 dspModule™
	with standard Heatsink installed
	Rugged IDAN® Configuration

Features:

• 3.3V & 5V PCI signaling compatible
• 1 GHz TMS320C6416 DSP
• 8000 MIPS operation
• Linearly Addressable PCI Interface 
• Eight 32-Bit Instructions/Cycle
• 1.0ns cycle time
• 32, 128 & 256 MB SDRAM
• 800 MB/s memory transfer rate
• 2 Mbytes FLASH
• All DSP resources accessible from the PCI bus
• VLIW instruction device
• Watch-Dog Timer
• Bus master or target only (Switch Enabled)
• Complete High performance DSP accelerator module
• Stackable 120-pin PCI expansion bus for use with PCI-104 and PC/104-Plus modules
• Stackable 80-pin PlatformBus (Buffered ASynchronous Memory Interface of the DSP)
• 3 Multi channel Buffered Serial Port (McBSP) (max. 75Mbit/s )
• Boot Mode: PCI, or Flash ROM Boot Mode (Switch Enable)
• All resources of the DSP can be accessed from the PCI bus
• TMS320™ DSP ALGORITHM STANDARD
• Mating Connectors
  • Standard 14-pin 0.1" DIL header (JTAG)
  • Standard 12-pin 0.1" DIL header (Power)
  • Standard 10-pin 0.1" DIL header (SyncBus)
  • 3 Standard 10-pin 0.1" DIL headers (McBSP)

I/O:

• Processor
• PlatformBus (3.3V)
  • 32 bit data
  • 16 bit address
  • Buffered ASynchronous Memory Interface of the DSP
  • High speed data transfer device between the DSP and the analog interface
• Three Multi channel Buffered Serial Ports (McBSP):
  • Buffered ASynchronous Memory Interface of the DSP 
  • High speed data transfer device between the DSP and the analog interface
  • TI/EI, MVIP, SCSA, ST bus, AC97 SPI Compatible
• JTAG emulator connector
  • Boundary-Scan-Compatible
• SyncBus for Synchronous operation
  • Up to 4 AIM6020HR Analog Interface Modules and/or
  • PC/104-Plus Data Acquisition boards
  • PCI-104 Data Acquisition board

• Supported under the following operating systems:
  • DOS (DPMI32)
  • Windows 98/NT4/2000/XP
  • Linux (2.4 and 2.6 kernels)
• Includes the RTD dspFramework, a suite of libraries and example programs to simplify application development.  Key features of the RTD dspFramework include:
  • Matching host-side and DSP-side libraries.
  • Standard interfaces for passing messages between the DSP and the host system.
  • Ability for the host to call DSP functions.
  • Support for single and multi-threaded applications (DSP/BIOS).
  • Support for on-board hardware (McBSP, SyncBus, Flash, etc).
  • DSP applications can be downloaded through the PCI bus, or programmed into the on-board flash.
  • Modular design and full source code makes it possible to modify and extend the framework.
• Source code, example programs, and API documentation are included for all supported platforms.
• TI Code Composer Studio required to develop and compile DSP applications.

• TI DSP TOOLS AND SOFTWARE

Physical Attributes:

• Size: 90mm L x 96mm W x 15mm H (3.6"L x 3.8"W x 0.6"H)
• Weight: Approximately 0.10 Kg (0.22 lbs.)
• Operating Temperature: -20° to +70°C: 90% humidity non-condensing
• Storage Temperature: -55° to +125°C
• Power requirements 1 GHz: 5.4 W @ 5 VDC typical

Documentation and Software Downloads:

• Contact RTD for documentation and software.

Ordering Information