SPM6020HR-233-16 Accelerator 
PCI-104 dspModule™
TMS320C6202 based Industrial DSP Module
Bus master or target only PCI Interface

	PCI Expansion Bus
Texas Instruments 233MHz TMS320C6202			SyncBus
			McBSP
			McBSP
JTAG			McBSP
	PCI        rotary switch	DSP PlatformBus
	SPM6020HR-233-16 dspModule™
	with standard Heatsink installed
	Rugged IDAN® Configuration

Features:

• 3.3V & 5V PCI signaling compatible
• 233 MHz TMS320C6202 DSP
• 1864 MIPS operation
• PCI Controller - PLX PCI9054 
• Eight 32-Bit Instructions/Cycle
• 4.3ns cycle time
• 16 Mbytes SDRAM
• 466 MB/s transfer rate
• 2 Mbytes FLASH
• All DSP resources accessible from the PCI bus
• VLIW instruction device
• Watch-Dog Timer
• Bus master or target only (Jumper Enabled)
• Complete High performance DSP accelerator module
• Stackable 120-pin PCI expansion bus for use with PCI-104 and PC/104-Plus modules
• Stackable 80-pin PlatformBus (Buffered ASynchronous Memory Interface of the DSP)
• 3 Multi channel Buffered Serial Port (McBSP) (max. 100Mbit/s )
• Boot Mode: Map1, Internal, HPI, or Map1, Internal, 16 Bit ROM Boot Mode (Jumper Enable)
• All resources of the DSP can be accessed from the PCI bus
• TMS320™ DSP ALGORITHM STANDARD
• Mating Connectors
  • Standard 14-pin 0.1" DIL header (JTAG)
  • Standard 10-pin 0.1" DIL header (SyncBus)
  • 3 Standard 10-pin 0.1" DIL headers (McBSP)

I/O:

• Processor
• PlatformBus (3.3V)
  • 32 bit data
  • 16 bit address
  • Buffered ASynchronous Memory Interface of the DSP
  • High speed data transfer device between the DSP and the analog interface
• Three Multi channel Buffered Serial Ports (McBSP):
  • Buffered ASynchronous Memory Interface of the DSP 
  • High speed data transfer device between the DSP and the analog interface
  • TI/EI, MVIP, SCSA, ST bus, AC97 SPI Compatible
• JTAG emulator connector
  • Boundary-Scan-Compatible
• SyncBus for Synchronous operation
  • Up to 4 AIM6020HR Analog Interface Modules and/or
  • PC/104-Plus Data Acquisition boards
  • PCI-104 Data Acquisition board

• DOS (DPMI32) driver with example programs.
• Windows 98/NT4/2000/XP driver with example programs.
• Linux driver with example programs.
• DOS and Windows drivers feature the RTD dspFramework, a suite of libraries and example programs to simplify application development.  Key features of the RTD dspFramework include:
  • Matching host-side and DSP-side libraries.
  • Standard interfaces for passing messages between the DSP and the host system.
  • Ability for the host to call DSP functions.
  • Support for single and multi-threaded applications (DSP/BIOS).
  • Support for on-board hardware (McBSP, SyncBus, Flash, etc).
  • DSP applications can be downloaded through the PCI bus, or programmed into the on-board flash.
  • Modular design and full source code makes it possible to modify and extend the framework.
• Source code, example programs, and API documentation are included for all supported platforms.
• TI Code Composer Studio required to develop and compile DSP applications.

• TI DSP TOOLS AND SOFTWARE

Physical Attributes:

• Size: 90mm L x 96mm W x 15mm H (3.6"L x 3.8"W x 0.6"H)
• Weight: Approximately 0.10 Kg (0.22 lbs.)
• Standard Operating Temperature: -40° to +85°C: 90% humidity non-condensing
• Storage Temperature: -55° to +125°C
• Power requirements 233 MHz:  3W @ 5 VDC typical

Documentation and Software Downloads:

• Contact RTD for documentation and software.

Ordering Information