SPM6030HR-233-16 Coprocessor
PC/104-Plus dspModule™
TMS320C6202 based Industrial DSP Module
Bus master or target only PCI Interface

	PCI Expansion Bus
Texas Instruments 233MHz TMS320C6202			SyncBus
			McBSP
			McBSP
JTAG			McBSP
	PCI        rotary switch	ISA Expansion Bus
	SPM6030HR-233-16 dspModule™
	with standard Heatsink installed
	Rugged IDAN® Configuration

  Features:

• 3.3V and 5V PCI signaling compatible
• 233 MHz TMS320C6202 DSP 
• 1864 MIPS operation
• PCI Controller - PLX PCI9054
• Eight 32-Bit Instructions/Cycle
• 4.3ns cycle time
• 16 Mbytes SDRAM
• 466 MB/s transfer rate
• 2 Mbytes FLASH 
• All DSP resources accessible
  from the PCI bus
• VLIW instruction device
• Watch-Dog Timer
• Bus master or target only (Jumper Enabled)
• Complete High performance DSP accelerator module
• Stackable 104-pin AT expansion bus
• Stackable 120-pin PCI expansion bus for use with PC/104-Plus and PCI-104 modules 
• 3 Multi channel Buffered Serial Port (McBSP) (max. 100Mbit/s )
• Boot Mode: Map1, Internal, HPI, or Map1, Internal, 16 Bit ROM Boot Mode (Jumper Enable)
• All resources of the DSP can be accessed from the PCI bus
• TMS320™ DSP ALGORITHM STANDARD 
• Mating Connectors
  • Standard 14-pin 0.1" DIL header (JTAG)
  • Standard 10-pin 0.1" DIL header (SyncBus)
  • 3 Standard 10-pin 0.1" DIL headers (McBSP)

I/O:

• Processor
• Three Multi channel Buffered Serial Ports (McBSP):
  • Buffered ASynchronous Memory Interface of the DSP 
  • High speed data transfer device between the DSP and the analog interface
  • TI/EI, MVIP, SCSA, ST bus, AC97 SPI Compatible
• JTAG emulator connector
  • Boundary-Scan-Compatible
• SyncBus for Synchronous operation with RTD's high performance:
  • PC/104-Plus Data Acquisition boards
  • PCI-104 Data Acquisition board

• DOS (DPMI32) driver with example programs.
• Windows 98/NT4/2000/XP driver with example programs.
• Linux driver with example programs.
• DOS and Windows drivers feature the RTD dspFramework, a suite of libraries and example programs to simplify application development.  Key features of the RTD dspFramework include:
  • Matching host-side and DSP-side libraries.
  • Standard interfaces for passing messages between the DSP and the host system.
  • Ability for the host to call DSP functions.
  • Support for single and multi-threaded applications (DSP/BIOS).
  • Support for on-board hardware (McBSP, SyncBus, Flash, etc).
  • DSP applications can be downloaded through the PCI bus, or programmed into the on-board flash.
  • Modular design and full source code makes it possible to modify and extend the framework.
• Source code, example programs, and API documentation are included for all supported platforms.
• TI Code Composer Studio required to develop and compile DSP applications.

• TI DSP TOOLS AND SOFTWARE

Physical Attributes:

• Size: 90mm L x 96mm W x 15mm H (3.6"L x 3.8"W x 0.6"H)
• Weight: Approximately 0.10 Kg (0.22 lbs.)
• Standard Operating Temperature: -40° to +85°C: 90% humidity non-condensing
• Storage Temperature: -55° to +125°C
• Power requirements 233 MHz:  3W @ 5 VDC typical

Documentation and Software Downloads:

• Contact RTD for documentation and software.

Ordering Information

dspModules™ Menu  /   PC104 Menu   /  Accessories   /   Development Kits   /   Home

Copyright © 1998-2008 RTD Embedded Technologies, Inc.  All rights reserved.