RTD Embedded Technologies, Inc. PC104 and PC104 plus embedded computers Home Page RTD Product Menu Single Board Computers Digital Signal Processing Frame Grabber SVGA Panel DVI MPEG Bluetooth WLAN 802.11 Cellular GSM GPRS GPS-Rail Ethernet Quad Serial CAN Bus USB 2.0 Modem PCMCIA GPS Hard Drives Power Supplies IDE & Floppy Up to 16 Bit Resolution 8 differential or 16 single ended inputs 16-bit 200 kHz throughput outputs FIFO buffer Channel Gain Table Pacer & Burst Clocks Programmable Gain Bit Programmable Opto-isolated Timer/Counters Incremental Encoders Servo Motor Control Synchro / Resolver DC/DC Isolated Avionics IDAN HiDAN HiDANplus Return to RTD's Home Page

PC/104, PC/104-Plus, PCI-104 & PCI/104-Express
 dataModule®  Selection Guide
 
     
 

Smart dataModule® SDM7540HR-8
with Autonomous SmartCal™

 
    PC/104-Plus & PCI-104 Smart Analog I/O & Digital I/O
    dataModules® with Autonomous SmartCal™

Smart Analog I/O & Digital I/O with
Autonomous SmartCal™
High Reliability (HR):  -40º to +85º C

PC/104-Plus Description OEM

 SDM7540HR-1

Autonomous SmartCal™ : Software independent on-demand auto-calibration by onboard Texas Instruments TMS320F2812 DSP
BUS MASTERING: Master or Target Only
ANALOG INPUT:  12-bit, 1.25 MHz, 8 differential or 16 single-ended, 1K FIFO buffer, 1024 entry channel gain table, pacer & burst clocks data markers, and programmable gain of 1, 2, 4, 8, 16, 32 & 64
ANALOG OUTPUT: Two channel, 12-bit, 200 kHz throughput, independent 1 K FIFO buffers
USER TIMER/COUNTERS: Three 16-bit 
DIGITAL I/O: 16 buffered TTL/CMOS lines. Two independent ports of  8 bits each. Port 0 is bit direction programmable. Port 1 is byte direction programmable. Advanced interrupt modes and bit masking. 
I/O PORTS:  SyncBus & McBSP Serial Ports
I/O CONNECTORS: One 26 pin .100" x .100" Header (analog)
                                     One 40 pin .100" x .100" Header (digital)
                                     One 10 pin .100" x .100" Header (McBSP)
                                     One 10 pin .100" x .100" Header (SyncBus)

$1195

 SDM7540HR-8

 SDM7540HR-1 with 8K FIFO buffer

$1345
PCI-104 Description OEM

 SDM8540HR-1

Autonomous SmartCal™ : Software independent on-demand auto-calibration by onboard Texas Instruments TMS320F2812 DSP
BUS MASTERING: Master or Target Only
ANALOG INPUT:  12-bit, 1.25 MHz, 8 differential or 16 single-ended, 1K FIFO buffer, 1024 entry channel gain table, pacer & burst clocks data markers, and programmable gain of 1, 2, 4, 8, 16, 32 & 64
ANALOG OUTPUT: Two channel, 12 bit, 200 kHz throughput, independent 1 K FIFO buffers
USER TIMER/COUNTERS: Three 16-bit 
DIGITAL I/O: 16 buffered TTL/CMOS lines. Two independent ports of  8 bits each. Port 0 is bit direction programmable. Port 1 is byte direction programmable. Advanced interrupt modes and bit masking. 
I/O PORTS:  SyncBus & McBSP Serial Ports
I/O CONNECTORS: One 26 pin .100" x .100" Header (analog)
                                     One 40 pin .100" x .100" Header (digital)
                                     One 10 pin .100" x .100" Header (McBSP)
                                     One 10 pin .100" x .100" Header (SyncBus)

$1195

 SDM8540HR-8

 SDM8540HR-1 with 8K FIFO buffer

$1345

         
    PC/104 & PC/104-Plus Analog I/O & Digital I/O dataModules®

Analog I/O & Digital I/O
High Reliability (HR):  -40º to +85º C

PC/104 Description OEM

DM6425HR-1

 ANALOG INPUT: 12-bit, 500 kHz 16 differential or 32 single ended, 32 word FIFO buffer, programmable acquisition sequencer
ANALOG OUTPUT: Four channel 12-bit 100 kHz throughput
USER TIMER/COUNTERS: Three 16-bit 
DIGITAL I/O: 32 buffered TTL/CMOS lines. Four independent ports of 8-Bits each. Port 0 is bit direction programmable, advanced interrupt modes and bit masking.  Port 1 is byte direction programmable.  Port 2 is output.  Port 3 is latched input.
I/O CONNECTOR: Two 50 pin .100" x .100" Headers

$ 795

 DM6425HR-8

 DM6425HR-1 with 8K FIFO buffer

$ 945

 DM6420HR-1

 ANALOG INPUT: 12-bit, 500 kHz 8 differential or 16 single ended, 1K FIFO buffer, channel gain table, pacer & burst clocks, DMA, data markers & programmable gain of 1, 2, 4 & 8 
ANALOG OUTPUT: Two channel 12-bit 200 kHz throughput 
USER TIMER/COUNTERS: Two 16-bit 
DIGITAL I/O: 16 buffered TTL/CMOS lines. Two independent ports of 8-Bits each. Port 0 is bit direction programmable. Port 1 is byte direction programmable. Advanced interrupt modes and bit masking. 
I/O CONNECTOR: One 50 pin .100" x .100" Header 

$ 695

 DM6420HR-8

 DM6420HR-1 with 8K FIFO buffer

$ 845

 DM6430HR-1

 ANALOG INPUT: 16-bit, 100 kHz 8 differential or 16 single ended, 1K FIFO buffer, channel gain table, pacer & burst clocks, DMA, & programmable gain of 1, 2, 4 & 8 
ANALOG OUTPUT: 2 channels 16-bit 200 kHz throughput 
USER TIMER/COUNTERS: Two 16-bit 
DIGITAL I/O: 16 buffered TTL/CMOS lines. Two independent ports of 8-Bits each. Port 0 is bit direction programmable. Port 1 is byte direction programmable. Advanced interrupt modes and bit masking. 
I/O CONNECTOR: One 50 pin .100" x .100" Header 

$ 695

 DM6430HR-8

 DM6430HR-1 with 8K FIFO buffer

$ 845
PC/104-Plus Description OEM

 DM7520HR-1

BUS MASTERING: Master or Target Only
ANALOG INPUT:  12-bit, 1.25 MHz, 8 differential or 16 single ended, 1K FIFO buffer, 1024 entry channel gain table, pacer & burst clocks data markers, & programmable gain of 1, 2, 4, 8, 16 & 32
ANALOG OUTPUT: Two channel, 12 bit, 200 kHz throughput, independent 1 K FIFO buffers
USER TIMER/COUNTERS: Three 16-bit 
DIGITAL I/O: 16 buffered TTL/CMOS lines. Two independent ports of  8-Bits each. Port 0 is bit direction programmable. Port 1 is byte direction programmable. Advanced interrupt modes and bit masking. 
I/O PORTS:  SyncBus & McBSP Serial Ports
I/O CONNECTOR: 3M 68 pin .50" x .100" Tri-polarized Shrouded Header mates with .050" x .100" Tri-polarized IDC Mini Socket 

$ 845

 DM7520HR-8

 DM7520HR-1 with 8K FIFO buffer

$ 995

    
     PC/104 Analog Output & Digital I/O dataModules®

Analog Output & Digital I/O
High Reliability (HR):  -40º to +85º C

PC/104 Description OEM

DM6620HR-1

 ANALOG OUTPUT: 12-bit 200 kHz 4 channel analog output module. Independent 1K FIFO buffer on each channel
DIGITAL I/O: Four data-marker output bits, 8 bit-programmable digital I/O lines with advanced interrupts, 8 port-programmable digital I/O lines
USER TIMER/COUNTERS: Six 16-bit
I/O CONNECTOR: One 50 pin .100" x .100" Header 

$ 695

DM6620HR-8

 DM6620HR-1 with 8K FIFO buffer

$ 795

DM6604HR

 ANALOG OUTPUT:12-bit 100 kHz 8 channel analog output module.
DIGITAL I/O: 24 digital I/O lines. 
I/O CONNECTOR: One 50 pin .100" x .100" Header 

$495

    
    PC/104 Analog Input & Digital I/O dataModules®

Analog Input & Digital I/O
High Reliability (HR):  -40º to +85º C

PC/104 Description OEM

 DM6210HR

 ANALOG INPUT: 12-bit, 40 kHz, 16 single ended and resistor configurable gain 
USER TIMER/COUNTERS: Three 16-bit 
DIGITAL I/O: 16 lines (four 4-bit ports) 
I/O CONNECTOR: One 50 pin .100" x .100" Header 

$ 395

    
    PC/104, PC/104-Plus & PCI/104-Express Digital I/O dataModules®

Digital I/O
High Reliability (HR):  -40º to +85º C     Extended Reliability (ER):  0º to +70º C

PC/104 Description OEM

DM6806HR

 DIGITAL I/O: 24 buffered 82C55 based digital I/O lines
USER TIMER/COUNTERS: Three 16-bit TIMER/COUNTERS. 
I/O CONNECTOR: One 50 pin .100" x .100" Header 

$155

DM6810HR

 DIGITAL I/O: 48 buffered bit programmable diode protected digital I/O lines. Advanced digital interrupt modes and bit masking.
USER TIMER/COUNTERS: Three 16-bit TIMER/COUNTERS. 
I/O CONNECTORS: Two 50 pin .100" x .100" Headers.

$245

DM6910HR

 DIGITAL I/O: 48 buffered bit programmable digital I/O lines. Advanced digital interrupt modes and bit masking.
USER TIMER/COUNTERS: Three 16-bit TIMER/COUNTERS. 
I/O CONNECTOR: 3M 68 pin .050" x .100" Tri-polarized Shrouded Header Mates with .050" x .100" Tri-polarized IDC Mini Socket. (Compatible with 68 pin IDC subminiature SCSI-3 female and male connectors) 

$245

DM6812HR

 DIGITAL I/O: 24 buffered bit direction programmable & 24 buffered port direction programmable diode protected digital I/O lines. Advanced digital interrupt modes and bit masking.
USER TIMER/COUNTERS: Three 16-bit TIMER/COUNTERS. 
I/O CONNECTORS: Two 50 pin .100" x .100" Headers.

$245

DM6912HR

 DIGITAL I/O: 24 buffered bit direction programmable & 24 buffered port direction programmable digital I/O lines. Advanced digital interrupt modes and bit masking.
USER TIMER/COUNTERS: Three 16-bit TIMER/COUNTERS. 
I/O CONNECTOR: 3M 68 pin .050" x .100" Tri-polarized Shrouded Header Mates with .050" x .100" Tri-polarized IDC Mini Socket. (Compatible with 68 pin IDC subminiature SCSI-3 female and male connectors) 

$245
PC/104-plus Description OEM

DM7820HR

 DIGITAL I/O: 48 diode protected digital I/O lines with 2MB input FIFO buffer.
USER TIMER/COUNTERS: Six 82C54 channels
I/O CONNECTOR: Two 50 pin .100" x .100" Headers. 

$495
PCI/104-Express Description OEM

DM9820HR

 DIGITAL I/O: 48 diode protected digital I/O lines with 2MB input FIFO buffer.
USER TIMER/COUNTERS: Six 82C54 channels
I/O CONNECTOR: Two 50 pin .100" x .100" Headers. 

$595


Specialty I/O Modules


    PC/104 Pulse Width Modulator & Digital I/O dataModules®

Pulse Width Modulator & Digital I/O
High Reliability (HR):  -40º to +85º C

PC/104 Description OEM

DM6816HR

 Nine 8-bit pulse width modulator outputs. 9 digital outputs.
USER TIMER/COUNTERS: three 16-bit.
I/O CONNECTORS: Two 50 pin .100" x .100" Headers

$245

DM6916HR

 Same as DM6816HR except with high density connector.
I/O CONNECTOR: 3M 68 pin .050" x .100" Tri-polarized Shrouded Header Mates with .050" x .100" Tri-polarized IDC Mini Socket. (Compatible with 68 pin IDC subminiature SCSI-3 female and male connectors) 

$245


    PC/104 Incremental Encoder & Digital I/O dataModules®

Incremental Encoder & Digital I/O
High Reliability (HR):  -40º to +85º C

PC/104 Description OEM

DM6814HR

 Three 16-bit incremental encoder channels. 6 digital I/O lines. 12 digital input lines.
USER TIMER/COUNTERS: three 16-bit. 
I/O CONNECTORS: Two 50 pin .100" x .100" Headers

$245

DM6914HR

 Same as DM6814HR except with high density connector.
I/O CONNECTOR: 3M 68 pin .050" x .100" Tripolarized Shrouded Header Mates with .050" x .100" Tripolarized IDC Mini Socket. (Compatible with 68 pin IDC subminiature SCSI-3 female and male connectors) 

$245

    
    PC/104 Opto-Isolated, Relay & Digital I/O dataModules®

Opto-Isolated Input & MOSFET Isolated Output
High Reliability (HR):  -40º to +85º C

PC/104 Description OEM

DM6852HR

 8 channel isolated MOSFET outputs. 4 Opto-isolated inputs with three selectable voltage ranges. 24 non-isolated 8255 based digital I/O lines. 
I/O CONNECTOR: 50, 48 & 16 .100" x .100" Headers. 
24 & 8 position terminal blocks optional for isolated lines.

$ 425

DM6854HR

 8 Channel Opto-isolated input module with 3 selectable voltage ranges. Advanced interrupt modes and bit masking. 4 isolated digital outputs (open collector). 24 non-isolated 8255 based digital I/O lines. 
I/O CONNECTOR: 50 & 48 .100" x .100" Headers. 
24 position terminal block optional for isolated lines

$ 389

DM6856HR

 16 Opto-isolated inputs,  +5V to +24V, 16 Opto-isolated outputs. 
I/O CONNECTORS: Two 50 pin .100" x .100" Headers 

$ 295

DM6858HR

 32 Opto-isolated inputs. 
I/O CONNECTORS: Two 50 pin .100" x .100" Headers 

$ 295

DM6888HR

 48 Opto-isolated inputs,  +5V to +24V, 16 Opto-isolated outputs.
I/O CONNECTORS: Three 50 pin .100" x .100" Headers 

$ 495

Relay Output
High Reliability (HR):  -40º to +85º C

PC/104 Description OEM

DM6952HR-H

 16 channel SPDT mechanical power relay output board with NO and NC contacts.  60VA switching capacity with voltages up to 220V 
I/O CONNECTORS: Two 50 pin .100" x .100" Headers 

$ 225

DM6952HR-S

 Same as DM6952HR-H except with screw terminal connectors
I/O CONNECTORS: Two 25 screw terminal connectors accepting 14-30 gauge wires 

$ 245

DM6956HR-H

 16 channel SPDT mechanical power relay output board with NO and NC contacts.  60VA switching capacity with voltages up to 220V 
16 Opto-isolated inputs,  +5V to +24V, 1000 Vrms isolation.
I/O CONNECTORS: Two 50 pin .100" x .100" Headers 

$ 377

DM6956HR-S

 Same as DM6956HR-H except with screw terminal connectors
I/O CONNECTORS: Two 25 screw terminal connectors accepting 14-30 gauge wires 

$ 398


PC/104 & PC/104-plus Field Programmable Digital I/O dataModules®

User Application Specific FPGA Digital I/O
High Reliability (HR):  -40º to +85º C
PC/104 Description OEM
FPGA6800HR FPGA designed by user
99 ESD protected digital I/O lines with 128K x 16 SRAM onboard.
I/O CONNECTOR: Three Standard 50-pin 0.1 inch spaced 2 x 25

$395
SK-FPGA6800HR Includes FPGA6800HR, Xilinx WebPack software DVD,
USB programming cable and ISA bus design book

$720
Custom
FPGA6800HR		 FPGA Custom designed by RTD
99 ESD protected digital I/O lines with 128K x 16 SRAM onboard.
I/O CONNECTOR: Three Standard 50-pin 0.1 inch spaced 2 x 25

RFQ
PC/104-plus Description OEM
Custom
FPGA7800HR		 FPGA Custom designed by RTD
48 diode protected digital I/O lines with 8MB SDRAM onboard.
I/O CONNECTOR: Three Standard 50-pin 0.1 inch spaced 2 x 25

RFQ

PC104 Menu   |  Accessories   |   Development Kits   |   Systems   |   Home

Copyright © 1998-2010 RTD Embedded Technologies, Inc.  All rights reserved.