Featuring Fail Safe, USB & Quick Boot Modes
SVGA			Audio COM 1 & 3   multiPort: Parallel Floppy aDIO™ Utility: Keyboard Mouse Speaker Battery Reset
LVDS   COM 2 & 4     2 USB 2.0   Ethernet   100Base-Tx   10Base-T
	Power	EIDE
	CMX158886CX1000HR Single Board Computer with Mini Fan Heatsink installed
PCI          (PCI-104)
	Rugged Fanless IDAN & HiDAN Configuration -40 to +85°C
	CMX158886CX1000HR-BRG-512 Single Baord Computer with ISA Bridge Module installed
CMX158886CX Bridge Module PCI Slot 0  ISA        (PC/104)			PCI  (PCI-104)
	Product modifications available upon request.

Features:

• 1.0 GHz  Intel Celeron M with thermal throttling
• Complete PC-compatible Single Board Computer
• Nonvolatile storage of CMOS settings without battery
• Stackable 120-pin PCI bus
  • 4 Bus master add-on cards capable
• 512 Mbytes or 1GB BGA DDR SDRAM (Surface-Mounted)
  • Up to 333 MHz Data Rate
  • ECC (Error Correction Codes) corrects single-bit memory
    errors and detects 2-bit errors (E512 model)
• 32-pin SSD socket:
  • Onboard Miniature Industrial ATA/IDE Flash Disk up to 8GB (4GB Standard)
  • Flash Disk PIO Mode with BIOS-configured write protect function (available upon request)
  • Natively supported by all major operating systems
• multiPort with Parallel Port and 18-bit Digital I/O Port with Advanced Digital Interrupt Modes
• 10/100 Ethernet with PXE Network Boot
• Four RS-232/422/485 Ports
• Two USB 2.0 (Universal Serial Bus) Ports
• EIDE Controller with UltraDMA 100
• 855GME SVGA controller Onboard with 3D Acceleration
• DirectX & OpenGL 3D Accelerator
• AC97 Audio Support
• Advanced power management features
• Advanced Thermal Management
  • Thermal Throttling reduces clock speed to
    prevent thermal runaway
  • Auto Fan Control only runs fan when needed
  • SMBus Temperature Monitor for CPU and board temperature
  • Mini Fan Heatsink with Auto Fan control
  • Passive Structural Heatsink & Heatpipes in IDAN and HiDAN System Configurations
• Advanced Programmable Interrupt Controller (APIC)
• 24 interrupt channels with APIC enabled (15 in legacy PIC mode)
• 3 timer/counter channels
• High resolution 100 MHz APIC timer
• RTD Enhanced BIOS with ACPI, USB Boot and Quick Boot modes
• Advanced Configuration and Power Interface (ACPI)
  • ACPI 1.0 Compliant
  • Supported power down modes: S1 (Power On Suspend), S3 (Suspend to RAM), S4 (Hibernate), and S5 (Soft-Off)
  • CPU Clock Throttling and Clock Stop for C0 to C3 Support
  • Also supports APM 1.2 for legacy power management
• 3.3V or 5V PCI bus signaling
• 400 MHz, source-Synchronous Front Side Bus
• Supports MMX and SSE2 instructions
• Math coprocessor
• Internal Cache
  • L1 - 32KB of instruction and 32KB data; L2 - 512KB
• Y2K compliant real time clock (external battery required)
• Watchdog timer
• PS/2 Mouse Port
• Keyboard Port
• Speaker Port
   

I/O:

• AC97 Audio Support
  • Selectable Headphone or Line level output
  • Line level input
  • Microphone input
• Fast Ethernet
  • Ethernet Controller
    • Intel 82562 Fast Ethernet PCI Controller
    • Integrated 3KByte Transmit and 3Kbyte Receive FIFOs
  • Physical Layer
    • 100Base-Tx and 10Base-T
    • Full Duplex support
  • Easy to Use
    • Low Power Features
    • LED Status
    • Software configuration
• 855GME SVGA controller for CRT and LVDS Flat Panel
  • Analog SVGA Output
  • LVDS Flat Panel output
  • Resolution up to 2048 x 1536 pixels with 32K colors
  • VGA, SVGA, XGA, SXGA, UXGA
  • Up to 16 million colors
  • 64-bit AGP Hardware graphics-accelerator
    • 2MB to 64MB of shared SDRAM high-performance memory
• Four BIOS configurable RS-232/422/485 serial ports on two connectors, each connect configurable as:
  • One full RS-232 port with TxD, RxD, CTS, RTS, DSR, DTR, RI, and CD
  • One RS-422/485 port with TxD+, TxD-, RxD+, RxD-, with 120 ohm termination jumper
  • Two RS-232 ports:
    • One with TxD, RxD, CTS, and RTS
    • One with TxD and RxD
  • One RS-232 port with TxD and RxD, and one RS-422/485 port with TxD+, TxD-, RxD+, RxD-, with 120 ohm termination jumper
  • Jumper enabled two RS-422/485 ports each with TxD+, TxD-, RxD+, RxD-, with 120 ohm termination jumper
  • 16550 compatible UARTs for high-speed
• multiPort function connector
  • Parallel port
    • SPP, PS/2 bi-directional, EPP & ECP
  • Advanced Digital I/O (aDIO)
    • Eight bit-programmable I/O with Advanced Digital Interrupt Modes
      • Event Mode Interrupt generates an interrupt when any input bit changes
      • Match Mode Interrupt generates an interrupt when input bits match a preset value
      • External Strobe Mode latches 8 data inputs and generates and interrupt
    • One 8-bit port programmable as input or output
    • Two Strobes can be configured as readable inputs.
  • Floppy controller interface - Interfaces only with RTD's XK-CM49 multiPort Floppy Drive and Cable Kit
• Two USB 2.0 (Universal Serial Bus) Ports
  • Supports 480 Mb/s (high-speed), 12Mb/s (full-speed), and 1.5Mbs (low speed) peripherals
  • 500 mA @ 5 Vdc provided per port
  • USB Boot capability
• UltraDMA-100 / 66 / 33 Master Mode PCI EIDE Controller
  • Transfer rate up to 100MB/sec using UltraDMA
  • Increased reliability using UltraDMA-33 transfer protocols
  • Support ATAPI compliant devices including DVD drives
  • 48-bit LBA support for hard drives larger than 137GB
• Utility port
  • XK-CM77 Cable Kit Included
  • PC-AT compatible keyboard port
  • PS/2 Mouse Port
  • Speaker (0.1W output) port
  • Hardware Reset input
  • Battery input for Real Time Clock
• Power I/O
  • Access to PCI-104 Bus pins
    • Gnd, ±12, 5 & 3.3 VDC
• Mating Connectors
  • Standard 12-pin 0.1" DIL header (Power)
  • Standard 10-pin 0.1" DIL header (Utility, COM1, COM2, USB, Ethernet)
  • Standard 10-pin 2mm DIL header (Audio & SVGA)
  • Standard 20-pin 2mm DIL header (Panel)
  • Standard 26-pin 0.1" DIL header (multiPort)
  • Standard 44-pin 2mm DIL header (EIDE)
     

Software:

• RTD Enhanced BIOS with built-in SETUP, USB Boot and Quick Boot Mode Installed
  • Supports onboard video and PCI expansion bus video.
  • Hard drives supported by onboard IDE controller.
  • Floppy drives supported via USB Port.
• Includes ROM-DOS , utilities and example programs.
• Compatible with all x86 operating systems:
  • MS-DOS, ROM-DOS, PC-DOS
  • Windows (98, NT 4.0, 2000, XP, and XP Embedded)
  • Linux (desktop and real-time versions)
  • RTOSes such as QNX, VxWorks, and Windows CE
    

Physical Attributes:

• Dimensions
  • Board Size: 90.17 mm L x 95.89 mm W (3.550 in L x 3.775 in W)
  • I/O Ext: 12.70 mm E_L x 79.38 mm E_W (0.500 in E_L x 3.125 in E_W)
• Weight: Approximately 0.14 Kg (0.30 lbs.)
• Standard Operating Temperature: -40 to +85°C: 90% humidity non-condensing
• Storage Temperature: -40 to +85°C
• MTBF
  • CMX158886CX1000HR-512:  279,926 hours
• Power requirements  1000 MHz:  10.9 W @ 5 VDC Typical
   

Recommended Accessories:

• Cable Kit XK-CM88
   

Documentation and Software Downloads:

• Hardware Manual
• Drivers and Example Programs
• Software Manual(s)
• Application Notes
   

Ordering Information

—  Sequentially laminated PCB fabricated in accordance with IPC-6012 Class 3 Standards  —
*OEM price includes soldered SDRAM (512MB or 1GB) and 4GB Flash Disk (8GB Flash Disk option available)
 

Third Party Information     IDAN® Systems

CPU Guide     PC104 Menu     Accessories     Development Kits     Home

Copyright © 1998-2012 RTD Embedded Technologies, Inc.  All rights reserved.